Overview

Cassette System

SmartView corrosion resistant, anodized aluminum cassette fascia cover and head rail offer a high level of flexibility.

• Head rail profile in White, Off White, Cream, Silver and Anodized Aluminum, with a channel designed to attach the back fabric panel.
• Cassette fascia cover in White, Off White, Cream, Silver and Anodized Aluminum, can be fabric covered. Fascia from some other systems can also be used.
• Aluminum tube and lift mechanisms made from high strength PE (45, 38 and 32 mm) are available. Or use your existing components of the same size.
• Standard ball-chain drive mechanism.
• Ball-chain in White, Cream, Gray and Black.
• System can be motorized.

Sliding bottom-bar tube and rail

The SmartView bottom bar tube and rails is a sliding system with two options depending on style and economic preference. The full system uses the sliding bottom tube with a low friction finish and color coordinated bottom bar end caps to connect the uniquely designed, sleek, oval bottom-bar rail in the SmartView cassette colors, also in Black. The hidden option uses only the sliding bottom-bar tube and especially designed, transparent, fabric guide end caps, which allow for an economical, hidden, bottom-bar style.

Mounting hardware

Both ceiling and wall mount brackets options are available in chrome finish. Both brackets provide quick and easy shade installation.

End cap

The SmartView cassette system end caps are made from high impact, flexible plastic and are secured to the head rail by three flush-mount screws. The end cap is designed to cover the edges of the cassette fascia cover and head rails for a more decorative appearance — available in the colors White, Cream, Gray and Black.

SmartView fabric collections.

SmartView offers a broad selection of fabric styles from select, high quality manufacturers, and ensures quality assurance through all shipment inspections.

Specs

Measuring

The first step to creating beautiful custom window treatments is recording accurate measurements.

*Record all measurements in inches and fractions of an inch, to the nearest 1/8”.

*Record measurements clearly and completely. Check and record all necessary information while on the job site. Do not rely on memory for details concerning measurements, obstructions such as handles, irregular trim, locks or out of square windows.

Installation

Note: **For Roller Shades with Standard Mounting Brackets, use Steps 1 thru 3. For Roller Shades with Fascia, use Steps 1 thru 5.

Tools Required:
Pliers
Carpenters level
Measuring tape
Power drill and drill bits
Screwdrivers or bits for drill

Starting installation: *The surface you are mounting shade on must be solid enough to support the weight of shade and tension created by operation of chain operated clutch. *Surface must be level or allow you to install mounting brackets level to each other.

STEP 1: Installing Mounting Brackets

There are two mounting brackets for each shade. One for the clutch end (has three rectangle shapes in center of bracket), and one for the idle end (has one circle shape in center of bracket). Position idle end bracket on correct side of opening in which you are mounting shade. Attach bracket using fasteners designed for surface you are mounting on. A minimum of two fasteners per bracket is recommended.

Refer to label on shade for shade width measurement, width will be the first number listed on label. Keeping that width in mind, measure from outside surface of bracket you just installed and mark position for next bracket. Position clutch end bracket at your mark and secure with fasteners.

STEP 2: Mounting Shade:

Position shade with fabric going over the top of roll and down the back side. The clutch side of the shade should line up with the clutch mounting bracket if they do not match the shade roll is backwards or you have not mounted the brackets correctly. When shade and brackets are lined up correctly you should insert the spring loaded idle end into the mounting bracket and push gently to compress spring. Then swing clutch end of shade into mounting bracket, line up the hook and nubs on the clutch with the bracket, insert into bracket and pull down gently to lock shade to bracket. Shade is now ready to operate. Remove shrink wrap from shade roll. Remove chain from bag. Allow chain to drop into its natural position. If you are using fascia mounting brackets  you need to install the chain guide at this time. Refer to parts drawing for correct positioning of parts. Insert the two screws provided to secure chain guide.

Safety Tension Device will be provided on all United Shade Contract roller shades to meet new safety regulations and standards. Fix the tension device to the wall or window frame with the provided screw per the instruction sheet. Critical Note: Installing the tension device with to much tension will make it hard for the ball stop to pass through and could cause chain breakage.

STEP 3: Positioning Ball Stop:

Ball stops have been supplied with your shade, which will be mounted on the chain to establish a top and bottom stopping point. Raise shade to the up most position of your choosing. Install the first ball stop on the top link of the chain; just before it enters the chain guide. Use a pair of pliers to pinch the ball stop onto the chain. Now lower the shade to the lowest position and install the second ball stop.

Critical Note: To insure you install ball stop on the correct side of chain watch the chain as you are raising shade and install first ball stop on the side of chain that is going up into chain guide, the second ball stop will be located on the opposite side of the chain.

Installation and Care Instructions: Westport Clutch Operated Roller Shade with Fascia

STEP 4: Installing Fascia (Shades with Fascia ONLY)

To install fascia simply hook the long side of the fascia over the top of the fascia bracket and then snap bottom side onto the bottom of the fascia bracket. Check to insure both ends of the fascia are secure to the fascia bracket.

STEP 5: Install Bracket Covers.

If your shade is mounted inside the window cavity you will most likely not use a bracket cover.

For all other shades snap covers onto end of bracket. When using fascia bracket covers, match the studs on the cover to the holes in bracket before snapping on.

Chain Operated Clutch Operating Instructions

It is strongly recommended to use two hands when operating (raising or lowering) the shade.

Lowering the Shade Pull the back chain (closest to the window glazing) down until the bead stop ball on the chain loop stops at the shade bracket and the shade hembar is approximately 1/2” above the window sill.

Raising the Shade Pull the front chain (furthest from the window glazing) down until the bead stop ball on the chain loop stops at the shade bracket and the shade hembar is at the top of the window.

Preventing Chain Breakage and Clutch Damage It is important to always use two hands when pulling on the bead chain. Pull the chain straight down. Do not under any circumstances pull the bead chain at an angle. Pulling the bead chain at an angle creates unnecessary pressure and strain on the bead chain and clutch. This action inhibits the intended operation of the clutch and can cause the shade to break When lowering the shade, do not let go of the bead chain as this action can cause the shade to lower quickly causing harm to the clutch or bead chain breakage. Allowing the bead chain to glide through the operators hands with gentle pressure assists in controlling the speed at which the shade will lower or raise. 

Installation of the Chain Safety Tension Device To prevent chain breakage and clutch damage as well as promoting product safety, it is imperative that the Chain Safety tension device shipped with every chain operated clutch shade be installed to the wall or window mullion. The Chain Safety tension device should be installed so that the bead chain and bead stop balls move smoothly through the opening of the device. Each chain operated clutch operated roller shade is shipped from the factory with the Chain Safety tension device pre-installed on the bead chain. Removal of this device or failure to properly install it, can cause damage to the clutch lifting mechanism and will result in the voidance of the product’s limited lifetime warranty.

Chain Operated Clutch Operating Instructions

It is strongly recommended to use two hands when operating (raising or lowering) the shade.

Lowering the Shade Pull the back chain (closest to the window glazing) down until the bead stop ball on the chain loop stops at the shade bracket and the shade hembar is approximately 1/2” above the window sill.

Raising the Shade Pull the front chain (furthest from the window glazing) down until the bead stop ball on the chain loop stops at the shade bracket and the shade hembar is at the top of the window.

Preventing Chain Breakage and Clutch Damage It is important to always use two hands when pulling on the bead chain. Pull the chain straight down. Do not under any circumstances pull the bead chain at an angle. Pulling the bead chain at an angle creates unnecessary pressure and strain on the bead chain and clutch. This action inhibits the intended operation of the clutch and can cause the shade to break When lowering the shade, do not let go of the bead chain as this action can cause the shade to lower quickly causing harm to the clutch or bead chain breakage. Allowing the bead chain to glide through the operators hands with gentle pressure assists in controlling the speed at which the shade will lower or raise. 

Installation of the Chain Safety Tension Device To prevent chain breakage and clutch damage as well as promoting product safety, it is imperative that the Chain Safety tension device shipped with every chain operated clutch shade be installed to the wall or window mullion. The Chain Safety tension device should be installed so that the bead chain and bead stop balls move smoothly through the opening of the device. Each chain operated clutch operated roller shade is shipped from the factory with the Chain Safety tension device pre-installed on the bead chain. Removal of this device or failure to properly install it, can cause damage to the clutch lifting mechanism and will result in the voidance of the product’s limited lifetime warranty.

Fabrics

Bocacio

Creations

Seasons

Woodsheer

Care

Roller Shades can be easily cared for by simply using soapy water or a mild cleaning solution on spots. However try a small area first. Harsh household cleaners or detergents may cause damage to fabric or loss of color. It is our recommendation to dust the rails and fabrics of the shades on a regular basis.

Diagrams

Twinlight catalog 10-09-2009 - Download PDF